Specifications

Installation

STEP 1) CLEANING

THE GLASS MUST BE AS CLEAN AND DUST FREE AS POSSIBLE! You will need a clean spray bottle with a strong pump. Fill the bottle with clean water prefferably filtered water. Add 1/2 teaspoon of amber colored baby shampoo to 1 quart of water in the spray bottle. DO NOT USE DETERGENT! The film is applied to the interior side of the window. Remove all obstructions from the work area. Decals may be tinted over if desired. Spray the solution on the glass and carefully scrape the entire glass with the razor blade scraper tool of your choice. Next, aggressively spray into the crevice around the entire window, use a tooth brush to scrub out any dust and dirt and rinse well, then rinse well again. Now you can squeegee window and dry around the edges with paper towels. You should soak up the dirty water on the window sill and wall with paper towels.

STEP 2) CUTTING FILM

The film has a thin plastic liner covering the adhesive side which will not be removed until after the film is cut, during the application stage. Unroll the film on the floor or on a table top. Cut it slightly larger than the glass area, 1″ margin is a useful size, more or less is a matter of preference or necessity, but you do not want to risk cutting the film smaller than the glass, because you could waste your materials. Spray the window with solution and then place the film on the glass with the adhesive/liner side towards the glass. The liquid will hold the film in place when you press it on the glass. You can move the film to reposition it, but spray more solution under film if you move it or it won’t stay up on the glass. Position the film with even overlap all around the edges of the window, then squeegee the film down into place there. Now you are ready to cut the film to the final size. You may also consider using the precision “factory edge” of the film as one of your edges. Use fresh and sharp stainless steel blades. Press carefully enough to cut through the film, but not so much that you cut into the glass. The general rule is to change blades for every window, don’t be cheap, it’s important!!!

STEP 3) APPLICATION

The film will be peeled and applied next. Now you will need to clean the window one last time with a squeegee and paper towels. ALWAYS WASH THE GLASS IMMEDIATELY BEFORE YOU APPLY THE FILM! Peel the backing from the film. Tthis step sometimes seems like the hardest part of the whole job. SPRAY the film as you peel. Spray more solution until it sheets down the entire film. Now carefully place the piece of film into exact position ans carefully peel back the film backing. Next, lightly squeegee down the center of the window to tack the film into it’s correct position. With film in final position, squeegee up and down from center, then sideways from the center. Squeegee the entire window vertically and horizontally from the center out to the edges, making a grid-type pattern. You should end at the 4 corners of the film last. Wipe water from the edges of the film with paper towels. The final step is to press all remaining moisture out with a hard card. You must squeegee the film again with this card, pushing hard to get out all the water, using the same pattern as described above and overlapping your strokes. The more water drops you get out, the better. This is a difficult step if done in direct sunlight, because the water starts to dry and the adhesive activates too fast. Water left under the film, between the film and the glass, will eventually vaporize out through the plastic. Excessive moisture from any spots missed by carding may form small water blisters that will take a little longer to dry, but they will eventually dry out. Normally, with good conditions and proper installation, the film will only look foggy for one or two days. In cold weather it may take a week or more. We recommend you wait a week or two before handling or touching the film to allow the adhesive to properly bond with the glass. Drying time will vary based on the weather conditions and temperature. Indoor temperature and indoor humidity are the main factors that will affect the drying time.

STEP 4) CLEANING

Now you may gently wipe the windows using a fine mist of solution and soft paper towels to clean any smudges or fingerprints, use only cleaners that DO NOT contain ammonia! Ammonia tends to dissolve the acrylic scratch resistant layer, causing the window film to fail and get damaged easier. A good cleaner for window film is the blue ALCOHOL based windshield cleaner solution from an auto supply. We recommend a non-ammonia cleaner and a soft cloth, such as microfiber. One part vinegar to 10 parts water), or Windex. If you use a professional window cleaning person let them know which windows are tinted.

Registration

"IntellIGuard" Solar Window Film


PRODUCT REGISTRATION

Registration form submitted!
We will also send you confirmation by email.

First Name	*This is not a valid name.*This field is required.
Last Name	*This is not a valid name.*This field is required.
Address 1	*This is not a valid name. *This field is required.
Address 2	*This is not a valid name. *This field is required.
City	*This is not a valid name.*This field is required.
State	Alabama Alaska American Samoa Arizona Arkansas California Colorado Connecticut Delaware District of Columbia Florida Georgia Guam Hawaii Idaho Illinois Indiana Iowa Kansas Kentucky Louisiana Maine Maryland Massachusetts Michigan Minnesota Mississippi Missouri Montana Nebraska Nevada New Hampshire New Jersey New Mexico New York North Carolina North Dakota Northern Marianas Islands Ohio Oklahoma Oregon Pennsylvania Puerto Rico Rhode Island South Carolina South Dakota Tennessee Texas Utah Vermont Virginia Virgin Islands Washington West Virginia Wisconsin Wyoming *This is not a valid name. *This field is required.
Zip	*This is not a valid name.*This field is required.
Phone	*This is not a valid phone number.*This field is required.
E-Mail	*This is not a valid email address.*This field is required.
Purchase Date	*This is not a valid name. *This field is required.
Company who Installed	*This is not a valid name.*This field is required.
Installers Name	*This is not a valid name.*This field is required.

Message *The message is too short.

clearsend

Return Policy

If for any reason you are not satisfied with your purchase, you may return the purchased product to GenerationalEnergy within thirty (30) days of the original date of purchase for a full refund including shipping with a *re-stocking fee, provided it has not been installed, in original packaging, and in new & resalable condition. Refunds for items returned within thirty days of the purchase date will be credited in the same form as the original payment type.

GenerationalEnergy Inc. WILL NOT ISSUE REFUNDS FOR EQUIPMENT THAT HAS BEEN PREVIOUSLY INSTALLED, DAMAGED, OR OTHERWISE RETURNED UNUSABLE FOR RESALE. Any damaged item must be reported within 7 days from . No refund after 30 days, no exceptions.

Please note, for ALL returns, you must first call GenerationalEnergy to authorize your return and get a return authorization number. All packages returned without prior authorization will be refused and sent back to shipper.

* Re-Stocking Fee

A 20% RESTOCKING FEE WILL BE DEDUCTED FROM ORIGINAL PURCHASE PRICE ON ALL ITEMS RETURNED WITHIN 30 DAYS.

Exchange Policy

If you wish to exchange your item, you may return the purchased product to GenerationalEnergy within thirty (30) days of the original date of purchase in exchange for another model provided it has not been installed, in original packaging, and in new & resalable condition. Exchanges will be charged a reduced re-stocking fee of 10%. GenerationalEnergy will assume shipping costs on item returned. Customer will be responsible for shipping charges of “new” item shipped.