Specifications

Installation

Pretreatment

1. Oil sample analysis of the installed refrigeration compressor oil should be taken if at all possible and mandatory in all cases where there is an accessible sump.
2. Benchmark (or pretreatment operation) data of the system should be taken and recorded prior to installation.
3. A qualified "Air conditioning & Refrigeration" (A/C&R) technician should perform a standard maintenance inspection before any refrigeration system is treated with IntelliBond. This inspection should, at a minimum, verify that the following conditions exist:
1. Head pressure and suction pressure within design limits.
2. Absence of oil or refrigerant leakage.
3. Coils, filters, strainers, etc. are clean and free of obstructions.
4. Thermostats or control systems functioning properly.
5. Heat exchanger coil fins free of dust, dirt, and corrosion.
4. Ensure that the maintenance person responsible for the system has obtained and is current on any manufacturer's maintenance bulletins or modifications to procedures or maintenance material.
5. Instruct maintenance personnel that IntelliBond will displace oil and carbon deposits on tube surfaces. Particularly in older systems, these deposits and oil returning to the compressor may clog in-line filters, separators, and driers and/or oil filters. It is mandatory that a substantial supply of the replaceable items mentioned be provisioned in advance of installation.

Residential Installation instructions

1. If the system is charged, start the unit and keep it running throughout the installation.
2. Introduce IntelliBond into the unit's cool gas suction line valve or low-pressure port on the refrigerant line.
3. An injection pump designed for the application should be used to ensure no contaminants are introduced.
4. It is important that neither air nor moisture be allowed to enter the system during this process.
5. The fluid is to be injected very slowly into the system. Observe the valve to avoid bubbling.
6. The FTA advises that if the system is smaller than 25 tons (88 kW) of cooling, the fluid may be introduced in a single treatment. However if more fluid is required, it is recommended to use two equal treatments to obtain the appropriate dosage.
7. It is not unusual to see a slight increase in energy consumption immediately following treatment as the fluid begins to move throughout the system and oil and other particles are displaced. Dividing the treatment into smaller doses minimizes this effect.

IntelliBond Alternative commercial Installations

1. If the system is discharged, introduce the appropriate dosage to the refrigeration oil before charging the system. If possible, remove an amount of refrigeration oil equal to the IntelliBond dosage.
2. For a small unit system that is under a charge, "Refrigerant Dye Injector" equipment may be used to introduce the IntelliBond treatment, at the correct ratio (see: IntelliBond Ratio Usage chart), into the unit's cool gas suction line valve or low-pressure port on the refrigerant line. Add IntelliBond to the system by the same procedures that are normally employed to add refrigerant dye to an A/C&R system. Alternatively, a standard set of A/C&R "technician pressure gauges" may be used to add the IntelliBond fluid by the following procedures: remove the low- pressure hose (blue), fill the hose with the IntelliBond fluid (by opening the valve at the bottom and inserting the fluid into the top of the hose. The hose will be full when the fluid runs out of the bottom of the hose). Reattach the hose to the gauge and slowly allow the gas to move the fluid out of the hose. Re-check pressures and disconnect. It is important that neither air nor moisture be allowed to enter the system through the hose during this process.

Post Treatment

IntelliBond may take one to two weeks of normal operation to disperse completely throughout the system. As the activated molecules bond to metal, they displace oil and carbon deposits on tube surfaces. In older systems, these deposits and oil returning to the compressor may clog in-line filters, separators, and driers and/or oil filters. Maintenance personnel are to observe the system frequently, especially in the first two weeks, and are to clean or replace the filter items as frequently as required.

AC & R Ratio Usage

1. IntelliBond should be added at a rate of 1 fl oz per ton of A/C or 10% of refrigerant oil volume * (1 ton = 12,000 BTU / h / / 3,52 kW)

Registration

"IntellIBond" HVAC Molecular
Bonding Agent


PRODUCT REGISTRATION

Registration form submitted!
We will also send you confirmation by email.

First Name	*This is not a valid name.*This field is required.
Last Name	*This is not a valid name.*This field is required.
Address 1	*This is not a valid name. *This field is required.
Address 2	*This is not a valid name. *This field is required.
City	*This is not a valid name.*This field is required.
State	Alabama Alaska American Samoa Arizona Arkansas California Colorado Connecticut Delaware District of Columbia Florida Georgia Guam Hawaii Idaho Illinois Indiana Iowa Kansas Kentucky Louisiana Maine Maryland Massachusetts Michigan Minnesota Mississippi Missouri Montana Nebraska Nevada New Hampshire New Jersey New Mexico New York North Carolina North Dakota Northern Marianas Islands Ohio Oklahoma Oregon Pennsylvania Puerto Rico Rhode Island South Carolina South Dakota Tennessee Texas Utah Vermont Virginia Virgin Islands Washington West Virginia Wisconsin Wyoming *This is not a valid name. *This field is required.
Zip	*This is not a valid name.*This field is required.
Phone	*This is not a valid phone number.*This field is required.
E-Mail	*This is not a valid email address.*This field is required.
Purchase Date	*This is not a valid name. *This field is required.
Company who Installed	*This is not a valid name.*This field is required.
Installers Name	*This is not a valid name.*This field is required.

Message *The message is too short.

clearsend

Return Policy

If for any reason you are not satisfied with your purchase, you may return the purchased product to GenerationalEnergy within thirty (30) days of the original date of purchase for a full refund including shipping with a *re-stocking fee, provided it has not been installed, in original packaging, and in new & resalable condition. Refunds for items returned within thirty days of the purchase date will be credited in the same form as the original payment type.

GenerationalEnergy Inc. WILL NOT ISSUE REFUNDS FOR EQUIPMENT THAT HAS BEEN PREVIOUSLY INSTALLED, DAMAGED, OR OTHERWISE RETURNED UNUSABLE FOR RESALE. Any damaged item must be reported within 7 days from . No refund after 30 days, no exceptions.

Please note, for ALL returns, you must first call GenerationalEnergy to authorize your return and get a return authorization number. All packages returned without prior authorization will be refused and sent back to shipper.

* Re-Stocking Fee

A 20% RESTOCKING FEE WILL BE DEDUCTED FROM ORIGINAL PURCHASE PRICE ON ALL ITEMS RETURNED WITHIN 30 DAYS.

Exchange Policy

If you wish to exchange your item, you may return the purchased product to GenerationalEnergy within thirty (30) days of the original date of purchase in exchange for another model provided it has not been installed, in original packaging, and in new & resalable condition. Exchanges will be charged a reduced re-stocking fee of 10%. GenerationalEnergy will assume shipping costs on item returned. Customer will be responsible for shipping charges of “new” item shipped.